TM 11-6625-2857-24 P
Code
Application/Explanation
h. Quantity Incorporated in Unit. Indicates the
D
- The lowest maintenance level capable of com-
quantity of the item used in the breakout shown on the
plete repair of the support item is the depot
illustration figure, which is prepared for a functional
level.
group, subfunctional group, or an assembly.
Z
- Nonreparable. No repair is authorized.
4. Special Information
(3) Recoverability code. Recoverability codes
a. The following publication pertains to the RF
are assigned to support items to indicate the disposition
Power Meter, Boonton Model 42BD and its components:
action on unserviceable items. The recoverability code is
TM 11-6625-2857-14, Manual for Micro WattMeter
entered in the fifth position of the Uniform SMR Code
(Boonton Model 42BD) with Power Detector 41-4E.
format as follows:
b. National stock numbers (NSN's) that are missing
Recoverability
from P source coded items have been applied for and
Code
Definition
will be added to this TM by future change/revision when
Z
- Nonreparable item. When unserviceable, con-
they are entered in the Army Master Data File (AMDF).
demn and dispose at the level indicated in
Until the NSN's are established and published, submit
position 3.
exception requisitions to: Commander, US
Army
L
- Reparable item. Repair, condemnation, and
Communications-Electronics
Materiel
Readiness
disposal not authorized below depot/
Command, and Fort Monmouth ATTN: DRSEL-MM, Fort
specialized repair activity level
Monmouth, NJ 07703 for the part required to support
c. National Stock Number. Indicates the National
your equipment.
stock number assigned to the item and will be used for
requisitioning purposes.
5. How to Locate Repair Parts
a. When National stock number or part number is
d. Federal Supply Code for Manufacturer (FSCM).
unknown.
The FSCM is a 5-digit numeric code listed in SB 708-
(1) First.
Using the table of contents,
41/42 which is used to identify the manufacturer,
determine the functional group within which the item
distributor, or Government agency, etc.
belongs.
This is necessary since illustrations are
e. Part Number. Indicates the primary number
prepared for functional groups and listings are divided
used by the manufacturer (individual, company, firm,
into the same groups.
corporation, or Government activity), which controls the
(2) Second. Find the illustration covering the
design and characteristics of the item by means of its
functional group to which the item belongs.
engineering drawings, specifications, standards, and
(3) Third. Identify the item on the illustration
inspection requirements to identify an item or range of
and note the illustration figure and item number of the
items.
item.
(4) Fourth. Using the Repair Parts Listing,
NOTE
find the figure and item number noted on the illustration.
b. When National stock number or part number is
When a stock numbered item is
known.
requisitioned, the repair part received
(1) First. Using the Index of National Stock
may have a different part number
Numbers and Part Numbers, find the pertinent National
than the part being replaced.
stock number or part number. This index is in NIIN
sequence followed by a list of part numbers in
f. Description. Indicates the Federal item name
alphameric sequence, cross-referenced to the illustration
and, if required, a minimum description to identify the
figure number and item number.
item.
(2} Second. After finding the figure and item
g. Unit of Measure (U/M). Indicates the standard of
number, locate the figure and item number in the repair
the basic quantity of the listed item as used in performing
parts list.
the actual maintenance function. This measure is
expressed by a two-character alphabetical abbreviation
6. Abbreviations
(e.g., ea, in, pr, etc). When the unit of measure differs
Not applicable.
from the unit of issue, the lowest unit of issue that will
satisfy the required units of measure will be
requisitioned.
(Next printed page is 4.1)
2
